Aloi za alumini za chuma

Aloi za alumini za chuma ni nini?

Alumini ni moja ya vifaa vya chuma vya mwanga na kiasi fulani cha vipengele vingine vya alloying vilivyoongezwa. Mbali na sifa za jumla za alumini, aloi za alumini zina sifa maalum za aloi kwa sababu ya aina tofauti na viwango vya vitu vya aloi vilivyoongezwa.. The density of aluminum alloy is 2.63～2.85g/cm, with high strength (σb is 110～650MPa), the specific strength is close to high alloy steel, the specific stiffness exceeds steel, with good casting performance and plastic processing performance, conductivity nzuri ya umeme na mafuta, good corrosion resistance and weldability, can be used as structural materials, in aerospace, anga, usafiri, ujenzi, mechanical and electrical, light chemical and It have a wide range of applications in aerospace, anga, usafiri, ujenzi, electromechanical, light chemical and daily necessities.

What are some common alloys of aluminum?

Metal aluminum alloy is a general term for alloys based on aluminum. There are different models, and the metal components added to various aluminum alloys are also different. The main alloying elements are Cu(shaba), Na(silicon), Mg(magnesiamu), Zn(zinki), Mhe( manganese), and the secondary alloying elements are Ni(nikeli),Fe( chuma), Ya(titani), Cr(chromium), Li(lithium), etc.According to the alloy series, inaweza kugawanywa katika:

Metal aluminum alloy series

• 1000 mfululizo wa alumini safi
• 2000 mfululizo wa aloi ya alumini ya chuma
• 3000 mfululizo wa aloi ya alumini ya chuma
• 4000 mfululizo wa aloi ya alumini ya chuma
• 5000 mfululizo wa aloi ya alumini ya chuma
• 6000 mfululizo wa aloi ya alumini ya chuma
• 7000 mfululizo wa aloi ya alumini ya chuma
• 8000 mfululizo wa aloi ya alumini ya chuma

Metal aluminum alloy raw materials are divided into

Hot selling metal aluminum alloys

1xxx series metal aluminum alloys

1xxx mfululizo:: 1050, 1060, 1070, 1100, 1200, 1235 na kadhalika

3xxx mfululizo: 3003, 3004, 3005, 3104, 3105 na kadhalika

5xxx mfululizo: 5005, 5052, 5083, 5086, 5454, 5754 na kadhalika

6xxx mfululizo: 6061, 6063, 6082 na kadhalika

Hot selling metal aluminum alloys tempers

According to temper, it can be divided into F, O, H, W, T

F temper

Free processing state Applicable to products with no special requirements for work hardening and heat treatment conditions during the molding process, the mechanical properties of the products in this state are not specified.

Ewe hasira

Annealed state Applicable to the processed products with minimum strength obtained by complete annealing.

H temper

the process-hardening state applies to products with increased strength through process hardening, and the products can undergo (or not) additional heat treatment to reduce the strength after process hardening.

Such as H11, H12, H13, H14, H15, H16, H17, H18, H19, H20, H21, H22, H23, H24, H25, H26, H27, H28, H29, H30, H31, H32, H33, H34, H35, H36, H37, H38, H39, H46, H48, H111, H112, H114, H116, H131, H321 na kadhalika

H temper breakdown

HXX The first digit after state H indicates the basic treatment procedure to obtain that state, as follows: H1 - purely work-hardened treatment state. Applicable to the state in which the required strength is obtained by work-hardening only without additional heat treatment.

H2 - Work-hardened and non-annealed state. It is applicable to the product whose strength is reduced to the specified index by not annealing after the degree of work hardening exceeds the requirements of the finished product. For the natural aging softened alloy at room temperature, H2 and the corresponding H3 have the same smaller ultimate tensile strength value; for other alloys, H2 and the corresponding H1 have the same smaller ultimate tensile strength value, but elongation is slightly higher than H1.

H3 - work-hardened and stabilized state. The H3 state is only applicable to alloys that are gradually age-softened at room temperature (unless stabilized).

H4 - Work-hardened and painted condition. For products that have been working hardened and then lacquered resulting in no annealing.

The second digit after H indicates the degree of work hardening of the product. Nambari 8 indicates the hard state. The sum of the lesser tensile strength of the O condition and the strength difference specified in Table 2 is usually used to specify the lesser tensile strength value of HX8. For states between the O (annealed) and HX8 states, a number from 1 kwa 7 should be added to the HX designator, and the number 9 should be added to HX to indicate a superhard state with a greater degree of work hardening than HX8.

W temper

Solid solution heat treatment state An unstable state, only applicable to the alloy after solution heat treatment, natural aging at room temperature, the state code only indicates that the product is in the natural aging stage.

T temper

Heat treatment state (tofauti na F, O, Jimbo la H) Applicable to products that have reached stability after heat treatment, na (au bila) kazi ngumu. the T designator must be followed by one or more Arabic numerals. The first digit after the T character indicates the basic type of heat treatment (kutoka 1 kwa 10), and the subsequent digits indicate variations in heat treatment details. For example T0, T2, T3, T4, T5, T6, T7, Q8, T24, T32, T35, T73, T74, T83, T351, T354, T650, T651, T851, na kadhalika

Surface treatment of metal aluminum alloys

Kulingana na matibabu ya uso, aluminum alloy sheets can be divided into two categories: non-painted products and painted products.

1) Non-painted products

1. They can be divided into hammered aluminum sheets (without regular pattern), embossed sheets (with regular pattern), and pre-passivated aluminum oxide surface treatment sheets.
2. These products are not painted on the surface of the plate, so the appearance of the surface is not high and the price is low.

2) Painted products

(1) Uainishaji.

According to the painting process can be divided into: painted board products and pre-roller coated boards.

According to the type of coating paint can be divided into: polyester, polyurethane, polyamide, modified silicon, epoxy resin, fluorocarbon, na kadhalika.

(2) A variety of coatings, the main performance difference is the resistance to ultraviolet rays of the sun, which in the front side of the most commonly used coating is fluorocarbon paint (PVDF), its ability to resist ultraviolet light is stronger; back side can choose polyester or epoxy resin coating as a protective paint. Zaidi ya hayo, a layer of peel-off protective film can be applied to the front side.

Nukuu ya Alumini ya Huawei